top of page

Laminate flooring on a solid floor: membrane, underlay, boards

Mark
Oct 17
6 min read

Laminate on a concrete screed needs a damp proof membrane first, then a rigid underlay, then the boards, because the slab gives off moisture and the fibreboard core of a laminate plank swells when it takes that moisture in. Laying a floating floor over concrete is the kind of work our handyman service takes on, and in this front room we laid one layer by layer, from the bare screed up. You walk into the room straight from the front door, so wet shoes and grit reach this floor before anywhere else. Timber floorboards change the order, with loose boards fixed down first and no plastic membrane on top.

The damp proof membrane goes down first, on the bare screed

Yellow plastic membrane laid in overlapping sheets over a bare concrete screed, part of the floor still uncovered
The membrane goes straight onto the screed, sheets overlapping, before any board touches the concrete.

The membrane went straight onto the bare screed, because a ground-floor slab keeps releasing moisture from beneath and a laminate core soaks up whatever reaches it. In the photo yellow sheets cover one side while the rest of the concrete is still bare. The sheets overlap, since moisture finds a gap between two edges as easily as open concrete. Without the sheet, vapour from the slab goes into whatever sits on top, and it shows first at the plank edges, where the core is exposed at the click joint.

From the concrete up, the layers in this room are:

  • the screed

  • a damp proof membrane

  • rigid fibreboard underlay

  • oak-effect laminate

A slab can look pale and dry on the surface while moisture still moves up through it. A moisture reading from a meter made for concrete, not a pin meter meant for timber, tells you whether the slab is dry enough to floor at all. It doesn't tell you the membrane can be left out, so lay it even when the reading is good. If there is underfloor heating pipe under the screed, tell your fitter before the underlay is chosen, since a thick fibreboard underlay insulates and holds the heat back from the room.

Laminate on a solid floor isn't the answer when the screed is visibly wet or has dark patches that keep spreading. A membrane slows moisture but does nothing about its source, so fix that first and let the slab dry. Laminate isn't the answer in a bathroom either, where water lands on the floor from above and the membrane underneath can't stop it; tiles, often laid over an uncoupling mat, suit a bathroom floor better. Real humps and hollows are a separate problem, usually solved with self-levelling compound first.

Rigid fibreboard underlay over the membrane, joints taped

Green and brown underlay boards laid over a screed, tape across the joints, yellow membrane showing by the front door
Rigid underlay boards going down over the membrane, tape across the joints, membrane still showing by the door.

Over the membrane we laid rigid fibreboard underlay rather than foam, because a stiff board bridges small dips in a screed while soft foam follows every one of them up into the laminate. The photo looks towards the open front door. The boards come in green and brown, the same size and in one layer, with joints staggered like brickwork and short pieces of tape across them. By the door and along the right-hand wall a strip of yellow membrane is still uncovered, with bare screed beyond it. A vacuum nozzle stands on the boards on the right. Grit left on the membrane ends up under a rigid board as a hard lump the laminate flexes over, so vacuum each area before boards go over it.

The joint between two click planks is the weak point of the floor. On soft underlay it sinks slightly under every step until the locking profile wears and the joint opens. A rigid board spreads that load, and the tape holds neighbouring boards in line so an edge can't ride up under the plank above.

If your screed is flat and smooth, foam will do. Otherwise check it before you buy with a long straightedge, turned to several angles. Thin slivers of light under it are what a rigid board can bridge; a wide gap under the middle, or a straightedge that rocks on a hump, means levelling the floor first.

First rows of laminate: joints staggered, boards on the underlay

Oak-effect laminate laid on green underlay boards, end joints staggered from row to row
Oak-effect boards going down on the underlay, end joints offset from one row to the next.

We laid the oak-effect boards with the end joints offset from row to row, because a click floor only shares load across rows when those joints don't line up. On the left of the photo the end joints step along the room instead of forming a line. A floating floor isn't fixed to anything, so it moves as one sheet when the room gets damper or drier. Staggered, each short joint is held by the long joints either side. Lined up, the floor gets a hinge running through it, and that is where a gap opens.

Start the next row with the offcut from the last, as long as it keeps the end joints well apart. Leave an expansion gap at the walls and around pipes, as the laminate maker's instructions set out, and hide it under skirting or scotia rather than filling it. A door frame cut too tight pins the edge and pushes the floor up into a hump.

Halfway across the front room: what a floating floor looks like mid-job

Front room mid-job: laminate along one side, taped underlay across the floor, membrane showing at the front door
Laminate along one side, taped underlay across the rest, boards stood against the right-hand wall.

Mid-job, the front room is two floors at once, laminate along one side and taped underlay over the rest, because a floating floor starts from one wall and grows row by row. The view looks towards the radiator on the left and the open front door on the right. Membrane still shows at the doorstep, and boards stand against the right-hand wall.

Starting against one straight wall gives the first row a fixed line, and every later row clicks into the one before. The row ripped down its length is normally the last, at the far wall, because a room rarely ends on a whole board width. If the starting wall itself is out of line, scribe the first row to it so the line every later row follows stays straight.

Because this room is the way in and out of the house, it takes heavy footfall, which is where a firm underlay earns its place. The membrane only stops moisture from below, so water walked in on shoes needs a mat inside the door. If you're living at home while a floor goes down, keep a clear route to the door and cover anything the dust can reach; we wrote more about protecting your home while work goes on.

A timber floor is a different job: fix the boards before anything goes on top

Bare pine floorboards with gaps between them in another house, a work platform and hammer in the middle of the room
A different house and a different base: pine boards stripped back, with gaps showing between them.

On a timber floor like the one in this other house, you fix down every loose board first and leave out the plastic membrane, because a sheet on top of timber holds moisture in the wood and a floating floor over a loose board flexes with every step. The photo shows stripped pine boards with gaps between them. On a ground-floor suspended floor, gaps like these let air rise from the ventilated void underneath, and that air helps keep the timber dry. Upstairs there is no ground moisture for a membrane to stop, so it has no job there either.

Walk a timber floor and listen. A board that moves or squeaks will do the same under laminate, and the floor above will bend there until its joints give. Screw down loose boards and plane off raised edges so the underlay sits flat. A split or soft board needs replacing.

Before you buy laminate, lift a corner of the old covering on a solid floor and look for dark patches, or walk timber boards for movement. If yours needs more than a membrane and the right underlay, it's work our handyman service covers, alongside jobs like repairing wet rot in a front door.

Questions about laminate on a solid floor

Do I need a damp proof membrane under laminate on a concrete floor?

Yes, concrete at ground level needs a damp proof membrane under laminate, either as a separate sheet or built into the underlay. In this room it was a separate sheet under the fibreboard, which doesn't carry a film of its own. Lap a separate sheet well at the edges and turn it slightly up the wall, then trim it once the skirting or scotia covers the edge.

Is green fibreboard underlay better than foam for laminate?

Green fibreboard suits a floor with shallow unevenness, and foam is fine where the surface is already flat and smooth. Fibreboard also tends to deaden footfall noise better than thin foam. Neither replaces levelling, because over proper humps a board rests on the high spots and flexes between them.

Can you put a plastic membrane under laminate on a timber floor?

On floorboards the usual answer is no, so choose an underlay without a plastic film unless the laminate maker's instructions say otherwise. On a ground floor, check the air bricks outside are clear, since blocked vents leave the void under the boards damp whatever goes on top.

Ready to Get Started?

​

👉 [Click Here to Contact Us] 

📧 Questions? Email us at Contactusm4@gmail.com — we’re happy to help.

Craftsmanship You Can See. Results You Can Trust.

We take pride in transforming spaces through high-quality workmanship and attention to detail. Here’s a look at some of our recent residential painting and decorating projects:

56D655D6-43C6-45E2-B3B8-68960935AD37-removebg-preview.avif

M4 Property Maintenance delivers high-quality painting, decorating, handyman services, plumbing repairs, bathroom upgrades and complete property maintenance across Virginia Water and surrounding areas.

Quick Links

Service Areas

Address

Location

Went worth Estate

Ascot

Virginia Water

Maidenhead

Windsor

Sunningdale

Sunninghill

M4 Property maintenance

Phone +447948510090

Email - contactusm4@gmail.com

​​

Privacy Policy

Cookie Policy

bottom of page