A kitchen splashback panel behind the hob: the wall before it and the joints after
A kitchen splashback panel gives the wall behind the hob a glossy face with no grout lines to scrub. In this kitchen the wall between the worktop and the wall cabinets carries a white panel with grey and black veining. It is not an endless sheet, though. It goes up once the cabinets, worktop and hob are in and the wall has been prepared for it. On a bigger wall it also has joints. If you are comparing panels with tiles, or planning the work through a handyman service, this kitchen from one of our jobs shows the wall behind the hob with brown adhesive marks before the panel went up, and a joint under the cabinet above the hob once the panel was in place.
The panel goes on after the worktop and hob, so the wall and worktop get prepared first

On this kitchen the cabinets, worktop and hob were in place before anything covered the wall behind the hob, because a splashback panel sits on the worktop and is measured from it. In the second photo the bottom edge of the panel rests on the worktop, so the worktop sets the level the panel starts from. If your kitchen is being replaced, order the panel once the worktop is down and the hob is in position.
Above, brown adhesive marks sit on the wall in a brick pattern, with the outlines of rectangles visible, and there is a vertical pencil line and two small holes. A panel is rigid and flat, so it bridges whatever stands proud of the wall and shows it as a bump or an edge that will not sit tight. Tiles and grout hide small lumps, though tiles still need a flat wall to sit level; a panel hides none of them. Take the marks and any lumps off or level them out, then run a straight edge over the wall so you know it is flat before anything is ordered.
We taped the back edge of the worktop with green masking tape before the panel went up. The worktop sits directly under the wall being worked on, so debris and drips land on it. If your worktop is already in, tape and cover it before anyone starts on the wall, as with taping and covering surfaces before work starts for decorating.
A splashback panel gives you a wall with no grout lines, but a bigger wall means joints to plan

Behind this hob the panel leaves no grout lines, but the strip under the cabinet above is a separate piece with a visible joint, because panels are made in sheets of a limited size and a wall larger than a sheet has to be joined somewhere. Under the cabinet a horizontal joint is plain to see, and the veining does not line up across it. The cabinet over the hob hangs higher than the one to its right, so the strip makes up the extra height. A second, vertical line runs within the strip. The pattern stays within its own piece, so it breaks where two pieces meet, and a vein that stops dead at a joint draws the eye.
Plan the joints before the panel is ordered and keep them where they are least seen.
on a line the eye already follows, such as the underside of the wall cabinets
in an internal corner, where two walls meet
behind a tall unit or another fixed item that will hide the line
away from the middle of the wall behind the hob, where you look most
If you have not picked a design yet, a plain colour hides a joint better than a veined one, with no vein to break.
Two double sockets are set into the panel beside the hob, on the left, under the wall cabinets. A panel has to fit around fixed points on the wall, so socket positions need to be known when the sizes are taken. Mark your sockets on the same sketch as your joints, so an opening does not land on a joint line.
If you are planning a panel behind your hob, check the wall and sketch where the joints and sockets fall against your cabinets, then see what our handyman service covers.
Kitchen splashback panel questions
Can you put a splashback panel over tiles?
It can go over tiles that are flat and firmly stuck, although grout lines and uneven tile edges may show through or stop the panel lying flat, so stripping the tiles and bringing the wall back to a level surface gives a better base. Tap the tiles with a screwdriver handle before deciding. A hollow sound points to a tile that is loose or only partly stuck, and either is a weak base for a panel.
Can a splashback panel go around sockets?
Yes, in this kitchen two double sockets sit on the panel left of the hob. Measure where the sockets sit, from the worktop and from the nearest cabinet edge, and hand those figures to whoever makes the panel, because the openings are set out from them.
Glass or acrylic splashback: how do you choose?
Choose by the heat coming off the hob in front of it and by how the panel will be fitted, either trimmed on site or made to a template before delivery. Whichever material you look at, ask the supplier which of those two routes applies, because a template fixes the sizes and socket openings at the point of order.




Comments