top of page

Looking after exterior timber: decking, gates and French doors

Mark
Sep 16
6 min read

The photos below come from several different jobs, so they are not the story of one house. Deck boards and joists rot where water lingers, open faces go grey under sun and rain, a gate drops under its own weight, and French doors break down at the glazing bars and bottom rails. So exterior timber maintenance starts with a different first check on each piece. Probe the joists, drop water on grey boards, look at the gap on the latch side of a gate and probe the bottom rails of the doors. Each check tells you whether you need a repair or just exterior painting and decorating on sound joinery.

Lift the boards before you judge the frame

Balcony deck stripped back to old joists on the roof covering, with packers and a new length of timber laid across
Deck boards lifted and the joist frame laid bare, with a new length of timber lying on top.

With the boards lifted on this balcony, the old joists sit bare on the roof covering on plastic packers, and this is when you can judge the frame, because once the boards go back they hide the tops of the joists, where water sits. Here the joists are dark and stained and the black covering beneath them is torn. Yellow packers hold the timber up off it, with metal hangers at the joist ends.

A deck board dries from the top in sun and wind, but its underside and the top of the joist it rests on stay damp far longer, since no air or sun reaches that joint. Packers lift the frame clear of the covering so rainwater can run away underneath and not sit against the wood.

Before any new boards go down, push a probe into the tops and ends of the joists, and check that the metal hangers at those ends are firm and not rusting through. Sound timber resists the blade; soft timber lets it sink. Check the covering too, because a tear under the frame lets water into the roof below and new boards would hide it. With the frame open, a failed section can still be cut out and replaced. Oil on fresh boards does nothing for a soft joist underneath them.

Why grey timber drinks oil unevenly

Paint scuttle of dark oil on grey weathered decking beside a freshly oiled timber edge board
Fresh oil against bare grey timber shows how far the weathering had gone.

On this edge board by a door threshold, fresh dark oil sits right next to bare silver-grey wood, and the contrast shows how far weathering goes, because sun breaks down the surface fibres and rain washes them out, so the oil has to get past loose grey fibre. The board is cracked along the grain under the fresh oil, and the deck boards around the scuttle are still grey and unoiled.

Loose grey fibre soaks oil up unevenly and then comes away with it underfoot, and cracks and end grain drink far more than the flat face, so oil brushed straight onto weathered wood goes on blotchy. If you want an even colour on a deck that has gone this grey, wash it and sand it back to bright wood before you oil, and give the end grain and the cracks more than the face. Go again when grey starts to show through and water soaks into the boards where it used to bead up, because that means the finish has worn out of the surface.

Where timber meets steel, keep the two finishes apart

Painter brushing a black steel frame beside horizontal timber boards, with masking tape and a protective sheet below
Masking tape on the steel, along the line where the timber boards meet the frame.

Here we are working on a black steel frame with timber boards set into it, with masking tape on the steel along its bottom rail and a sheet along the base, because metal paint that lands on timber seals the grain and oil or stain that lands on steel leaves a surface the paint will not grip.

Steel takes a metal primer and a metal topcoat that sit on the surface as a sealed film, as on a steel door when you are repainting a garage door. Timber meant for oil or stain needs its grain left open, so the finish can soak in and the wood can move with the weather.

So treat the metal and the wood as two separate jobs, and cover whichever material you are not working on. Tape along the joint and a sheet at the base keep each finish on its own material, which is the same thinking as protecting the surfaces around the job indoors. When you finish timber set into a painted frame, the tape goes on the steel side of the line.

What to check on a ledged and braced side gate

Black ledged and braced timber side gate with galvanised tee hinges and a ring latch between white brick walls
Finished side gate, hung on galvanised tee hinges with a ring latch on the closing side.

This finished side gate is ledged and braced and hangs on two galvanised tee hinges with a ring latch on the closing side, and a gate built this way drops at the free end once the hinges and the frame stop carrying the weight of the latch side.

The long arm of a tee hinge spreads the load along the ledge, but when the screws work loose or the timber shrinks, the latch-side corner starts to sink.

On your own gate, check that:

  • the gap on the latch side is even from top to bottom

  • the latch drops into its keeper without you lifting the gate

  • the free corner clears the ground and does not scrape the base

  • the hinge screws are tight and the hinges sit flat and firm on the post or wall batten.

If a new gate is being hung for you, make the same checks before you accept it. If the gap tapers or you have to lift the gate to latch it, tightening the hinges helps only while the frame is still square and the hinge post stands upright and firm. A frame that has racked needs pulling back into shape before any paint goes on, or the new finish cracks along the joints.

French doors: the glazing bars show the finish first

Lower half of white painted timber French doors: glazing bars, lever handle, bottom rails and a dark threshold
Painted French doors, finished: glazing bars, stiles and bottom rails in an even white finish.

On these French doors the white finish is even across the glazing bars and down to the bottom rails, and with this many panes the glazing bars are where a rushed job shows first, because each bar has two faces and two edges against the glass where paint either builds up or skips.

The bottom rails and the joints just above them take the most water. Rain runs down the glass and the bars and collects on the rail, so paint cracks there first, and water then gets into the end grain of the joint.

When you paint doors like these, start with the glazing bars, move on to the horizontal rails and finish with the stiles, much as when painting a panelled door, in thin layers, so the wet edges meet along the long straight runs and not in the corners of the panes. Before any of that, press a probe into the bottom rails and the joints at their ends. If it sinks, you are looking at wet rot in a timber door, which is a repair to make before any paint. If the rail holds, scrape any cracked paint back to a sound edge and prime the bare wood before you repaint.

To go over your own exterior timber, take it in the order of this piece, starting with the frame under the boards, then the surface under the oil, the shape of the gate and the timber under the paint. If it all comes up sound and only needs finishing, our painting and decorating work covers the finishing side of exterior joinery.

Questions about exterior timber maintenance

Is decking oil or stain better for weathered timber?

On timber that has already gone grey, a penetrating oil is the easier choice to keep up, because it soaks into the wood and can be refreshed over a clean surface, while a coloured stain that forms a film wears through first where feet and furniture move. A half-worn film leaves a patchwork of colour and bare wood that is hard to blend without taking the whole board back.

Should I use a water-based or oil-based stain?

Choose by the surface you already have, so over a previous oil finish stay oil-based, and keep a water-based stain for timber sanded to clean, bare wood. Water-based products laid over oily timber tend to sit on the residue and peel; if you cannot tell what went on before, drip water on a hidden board, and if it beads on a dry board, some finish is still in the surface, so stay oil-based or sand back to bare wood first.

How do you keep paint off the glass on French doors?

Cut in with a small angled brush and let the paint run a hair onto the glass, since that thin overlap seals the joint between bead and pane, then scrape the excess off with a sharp blade when the paint is hard, rather than masking each pane. Keep the blade flat and stop short of the overlap so the seal stays.

Comments


Ready to Get Started?

​

👉 [Click Here to Contact Us] 

📧 Questions? Email us at Contactusm4@gmail.com — we’re happy to help.

Craftsmanship You Can See. Results You Can Trust.

We take pride in transforming spaces through high-quality workmanship and attention to detail. Here’s a look at some of our recent residential painting and decorating projects:

56D655D6-43C6-45E2-B3B8-68960935AD37-removebg-preview.avif

M4 Property Maintenance delivers high-quality painting, decorating, handyman services, plumbing repairs, bathroom upgrades and complete property maintenance across Virginia Water and surrounding areas.

Quick Links

Service Areas

Address

Location

Went worth Estate

Ascot

Virginia Water

Maidenhead

Windsor

Sunningdale

Sunninghill

M4 Property maintenance

Phone +447948510090

Email - contactusm4@gmail.com

​​

Privacy Policy

Cookie Policy

bottom of page